EPDM Coatings N.E Sales Office 494

CALL TO PLACE YOUR ORDER: 610-298-1989 ext 9

TANK/ROOF SPREADER

As a roofer you want to sell as many jobs as you can. As a building owner you want to save time and money but most roofing tools you’ve tried just seem to get in your way. They’re flimsy and unreliable, inefficient and messy. It’s frustrating because your reputation (and your bottom line) depends on your ability to get the job done right and on time.

Why choose a Tank Spreader?

  • Efficiently apply any pourable material, such as adhesives and coatings
  • Achieve even, consistent coverage with simple, gravity-driven application
  • Accurately cover either flat or ribbed roofs without messy overspray
  • Reduce waste with pre-drilled holes
  • Decrease downtime with easy refills
  • Enjoy simple clean-up and disposable or easy-to-replace parts
  • Apply coating over metal roof panels using 14” Tank Spreader
  • Easily purchase additional rollers

Customized rollers are also available for corrugated metal roofs

EPDM
EPDM
EPDM

This div will be used as the image description. HTML is supported.

EPDM

This div will be used as the image description. HTML is supported.

Description

All spreaders are gravity-fed and have disposable rollers. All parts are disposable or simple to replace. Tank Spreaders apply any pourable material such as low VOC adhesives and coatings from a tank.

Additional information

WEIGHT N/A
DIMENSIONS N/A
WIDTH Singlewide 14", Doublewide 27", Super 40"
PROFILE STYLE Standard, AG Profile, R Profile (PBR), HI R Profile, Snap Lock Profile, Single Lock Profile, Trapezoid Profile
REPLACEMENTS PARTS AVAILABLE Single, Double, or Super Wheel Axle Assembly; Single, Double or Super Roller Axle Assembly

FAQs

After each use, allow the adhesive to drain from the drain hole. It is best to wipe tank walls and hole edges before the adhesive sets up. Spray all tank surfaces with silicone spray before each use to aid in removal of hardened material.

Distribution ports can be increased with a drill bit. It is best to open the holes in increments of 1/16 at a time and usually only the center most holes.

The 14" Singlewide is best for roofs under 100 squares and in cut up areas with penetrations. The 27" Doublewide is a good balance of maneuverability and productivity. Usually used on projects from 50 squares to 500 squares. The 40" Superwide Tank Spreader offers unmatched productivity, as the operator walks along a 40" (1 Meter) swath of material.

Teflon tape on the wheels protects them from glue and coatings.

These two holes are optional. They are to be used when applying Bonding Adhesive where no running puddle is needed. When applying coating, it is helpful if the end holes are closed to allow the running puddle to diminish toward the ends of the roller.

To ground the BetterSpreader and/or TankSpreader you purchased:

  • Attach a wire to any bolt on either side of the product and
  • Attach the other end of the same wire to the steel deck or other grounded conductor such as a steel soil stack or metal roof deck. Attaching this end of the wire to a non-grounded conductor such as plastic or wooden material is NOT proper grounding.
  • Attach a Guide ground wire during use.
  • Prevent ground wire from contacting with flammable liquids, electrical wires or equipment. Reel in ground wire, whenever possible.
  • Ensure work crews are aware of the ground wire location at all times, and
  • Prevent unauthorized people from entering the work area.

When using a flammable liquid with the Better Spreader, care should be taken to avoid creating a spark. An electric drill should NOT be used with flammable liquids, as the motor may generate a spark. If using a flammable liquid, utilize a non-sparking Beryllium/Copper Scratch Awl to open holes in the pail.

We hope your next project is both safe and profitable.